Activators Rules and Guide
Support by Carlo IK1HJS – on WhatsApp +39 347 268 2466
World Wide Award – Regulations for Activators
1. Purpose
The purpose of the activators is to keep your special callsign active throughout the duration of the Award to allow hunters to earn points in as many as possible bands and modes.
2. Mandatory real-time QSO
All activators must have an Internet connection and are required to enter their QSO data on the platform provided by Hamaward in real-time. Only in exceptional cases may the entry of QSOs be permitted retroactively.
Our Hamconnect software and your browser are configured to SAVE all the QSOs if there is no Internet connection and you have logged offline some QSOs. As soon as Internet comes back all the QSOs are automatically reloaded on the platform without needing your help.
If QSOs are lost for any other reason, send as soon as possible and within 24 hours the ADIF of your log (you can send the entire log) to iw1fru@gmail.com, specifying the activator call sign (e.g., PD0KH.adi). The continuous loss of QSOs, often reported by hunters, is not in line with the spirit and ethics of this radio activity.
3. NO Contest allowed
The use of your special callsign is not allowed for any contests during the Award period. It is therefore not allowed to operate as a contest station by sending reports compatible with contest rules or calling "CQ Contest". It is allowed to receive calls from contest stations, but replying with a report compatible with the ongoing contest is not permitted. It is recommended to occasionally announce "No contest" during any overlapping contest activity.
4. Only one signal
It is required to have only one signal per band and mode for each special callsign.
By activating your special callsign on the Hamaward platform for an event, you accept and subscribe to these regulations.
Before you start
  • You must be registered on https://hamaward.cloud with your personal callsign and email (Create account), and you must have received the confirmation email. If not, please contact Max IW1FRU at iw1fru@gmail.com.
  • Log in, then click on your callsign (top right): you are in your Dashboard. Everything in this guide starts from the menu on the left.
Do you type your QSOs by hand?
If you work only SSB, or CW without keyboard transmitting, or FT8 or RTTY "manually", you don't need HamConnect and you can skip steps 1 to 4.
  • In the menu on the left, click Award list, then the orange Award Log button of the current WWA log.
  • Select band and mode, type the callsign you worked and click ADD QSO. You will see it scrolling down in the log.
  • After typing the callsign, press the space bar: you get a lookup of that callsign on qrz.com.
  • If something goes wrong, you can edit each QSO on the right side of the QSO line (remember to "save" after corrections). Only the QSO owner can do that.
For CW with keyboard transmitting and DIGITAL MODES you will use a separate logging program (N1MM, WSJT-X, JTDX, MSHV, DXLog, Win-Test…) connected to Hamaward with HamConnect: follow the steps below, once.
1Install and start HamConnect
  • In your Dashboard, click HamConnect in the menu on the left and download HamConnect for your computer (Windows, macOS, Linux). It will overwrite the old one if you had one before.
  • While installing, leave the default parameters. If your antivirus or Windows Defender asks for permission (HamConnect uses a network port), confirm and finish. Once installed, there is no need to do it again.
  • Start HamConnect. No window opens on the screen! Its icon appears next to the clock (Windows) or in the menu bar at the top of the screen (Mac). If the icon is not there, nothing will work.
  • Start HamConnect every time you turn on your computer.
  • Use Chrome or Firefox: Safari cannot connect to HamConnect.
2Connect the HamConnect page to HamConnect
  • With HamConnect running, open the HamConnect page (menu on the left) and click the green button Connect to HamConnect.
  • When it works, you see Connected to HamConnect! and the button turns red: Disconnect from HamConnect.
  • It doesn't connect? Check that HamConnect is running (its icon is there) and click again.
  • Still no luck? Click Advanced settings: the HamConnect Server Port must be the same as in HamConnect (click the HamConnect icon, then Settings). Normally it is 7351 on both.
  • In UDP QSO Broadcast you find three settings. UDP receive port is the important one: it must be the same number you set in your logging program, normally 12060. Leave Bind address at 0.0.0.0 and Multicast group as it is.
Hamaward HamConnect page
The HamConnect page: connection, UDP QSO Broadcast and Rig Monitor.
3Set up your logging program
  • Every logging program has a setting to send the logged QSOs over the network, usually called UDP or Broadcast. Set it to address 127.0.0.1 (this computer) and port 12060.
Important: set the special callsign in your program
Every QSO carries the callsign set in your logging program. Hamaward saves the QSO only if this is the special callsign you are activating: set the special callsign in your program, not your personal one.
With a different callsign, your QSOs appear in red as ERROR in the Award Log and are not saved.
Open your program below for the exact steps:
BBlogger
  1. Use a log that belongs to the special callsign: click Log → Add new User, enter the special callsign and create a log for it.
  2. Click Tools → Configuration/Maintenance → QSO UDP Broadcast.
  3. In UDP 1, type 127.0.0.1 in IP/Host and 12060 in Port, and choose the ADIF format.
  4. Open the New QSO window (F2) and click the UDP1 button: it turns red when sending is on.
DXLog
  1. Click File → New and create your log with the special callsign.
  2. Click Options → Configure network. In QSO UDP broadcast, type 127.0.0.1 in IP addresses and 12060 in Ports. Click OK.
  3. Click Options and tick Enable network.
  4. Click Options → Broadcast and tick QSO.
Ham Radio Deluxe
  1. In the HRD Logbook, click Tools → Configure → My Station and type the special callsign in Callsign.
  2. Click Tools → Configure → QSO Forwarding.
  3. In UDP Send, turn on sending, type 127.0.0.1 in Send Address and 12060 as port.
  4. Click OK.
JTDX (version 2.2.158 or higher)
  1. Click File → Settings, open the General tab and type the special callsign in My Call.
  2. Open the Reporting tab. In Send logged QSO ADIF data, type 127.0.0.1 in 2nd UDP server and 12060 in UDP port.
  3. Tick Enable sending to secondary UDP server.
  4. Click OK.
JTDX Settings, Reporting tab
JTDX Settings, Reporting tab
Your QSOs are sent when you log them (Log QSO, then OK). To be asked after every QSO, tick Prompt me to log QSO in the Reporting tab.
Log4OM
  1. Click Settings → Program Configuration.
  2. Open Station Information and type the special callsign in Callsign.
  3. Open Software integration → Connections and add an outbound UDP connection: type ADIF_MESSAGE, address 127.0.0.1, port 12060. Make sure it is active.
  4. Click Save and apply.
LogHX
  1. Click Setup → General Setup and open the Broadcast Data tab.
  2. In Send (N1MM format), tick Contact, type 127.0.0.1 as IP address and 12060 as port. Leave Radio and Spots unticked.
  3. Click OK. If your QSOs are not sent, close and reopen LogHX.
MSHV
  1. Click Options → Macros and type the special callsign in My Call.
  2. Open the Network Configuration tab. In UDP Broadcast Settings, tick only Logged QSO ADIF.
  3. Type 127.0.0.1 in Server and 12060 in Port, click Reconnect and close the window.
MSHV, Network Configuration tab
MSHV, Network Configuration tab
N1MM Logger+
  1. Click Config → Change Your Station Data and type the special callsign in Call.
  2. Click File → New Log in Database, choose the log type DXPEDITION and click OK.
  3. Click Config → Configure Ports, Mode Control, Winkey, etc. and open the Broadcast Data tab.
  4. Tick Contacts and All Computers. In the field next to them, type 127.0.0.1:12060.
  5. Click OK.
N1MM Logger+ Configurer, Broadcast Data tab
N1MM Logger+ Configurer, Broadcast Data tab
QARTest
  1. In the window that opens with QARTest, click Create new Log. Choose the contest DXPedition, type the special callsign and click OK, then choose your bands and modes.
  2. Click Options → External Broadcast Data.
  3. Tick QSO, type 127.0.0.1 as IP address and 12060 as port.
  4. Click OK.
QLog
  1. Click Settings, open Station and type the special callsign in your station profile.
  2. Open Network. In QSO Changes, type 127.0.0.1:12060.
  3. Click OK.
Swisslog
  1. Click Options → My QTH and type the special callsign in MyCall.
  2. Click Options → Online Logbooks and open the UDP tab.
  3. Turn on sending, type 127.0.0.1 as IP address and 12060 as port, and choose one format only: ADIF.
  4. Click OK.
Win-Test
  1. Click File → New and create your log with the special callsign.
  2. Click Options → Configure interfaces.
  3. Tick Enable local network. Type 127.0.0.1 as Broadcast address and 12060 as Port number.
  4. Click OK.
WriteLog
  1. Click Setup → WriteLog Options → UDP Broadcast.
  2. For QSOs, tick Enable, type 127.0.0.1 as Address and 12060 as Port number. Click OK.
  3. Click Setup → Save Configuration.
WSJT-X
  1. Click File → Settings, open the General tab and type the special callsign in My Call.
  2. Open the Reporting tab. In Secondary UDP Server (deprecated), tick Enable logged contact ADIF broadcast.
  3. Type 127.0.0.1 in Server name or IP address and 12060 in Server port number.
  4. Click OK.
WSJT-X Settings, Reporting tab
WSJT-X Settings, Reporting tab
Leave the UDP Server section as it is: programs like JTAlert and GridTracker use it. Your QSOs are sent when you log them (Log QSO, then OK).
If you use more than one program (for example N1MM and WSJT-X), set the same UDP port in all of them, so you never have to change it.
4Test the connection
  • On the HamConnect page, in UDP QSO Broadcast, leave the port at 12060 and click Start UDP Broadcast.
  • Log a test QSO in your program (with IK1HJS, for example). The HamConnect page is just a demo: test QSOs are never saved in any log, so you can test what you want, as long as you want.
  • In the UDP QSO TEST box, a green TEST DONE line appears with the QSO data: time, band and mode must be correct.
A successful test: TEST DONE in the UDP QSO TEST box
A successful test: the QSO arrived with all its data.
  • The last column shows the callsign your program sends. Check that it is the special callsign: the test does not check it for you.
  • Red ERROR? The red word tells you what to fix in your program. For example, Activator Error means that no callsign is set in your program; Band Error or Mode Error means that Hamaward doesn't accept that band or mode.
  • Nothing appears? Check that the page says Connected to HamConnect!, that you clicked Start UDP Broadcast, and that the port is the same in your program and on the page. Sometimes changing the port number on both sides can help (12061 instead of 12060).
5Go on air in the World Wide Award
  • Start HamConnect and check that its icon is there. Start your logging program with the special callsign set (step 3).
  • Open your browser, log in on hamaward.cloud and click Award list, then the Award Log button of the World Wide Award.
  • To go on air YOU MUST BE ON YOUR AWARD LOG PAGE and keep this page open while you operate. No need to have focus on it: it can stay in the background.
  • Top right there is a green Start UDP button: press it if you are using a logging program. From now on, every QSO you log in your program is saved in your Hamaward log.
  • If you type your QSOs directly on the web page, press the red Stop UDP button: the manual entry form appears.
  • Before you start transmitting press the "Go OnAir" button, and press "Go OffAir" when you close your radio activity. Repeat it every time you go on air: this is how hunters see that you are active. After 5 minutes of inactivity you return as "not active" operator.
  • Check on the page that your first QSOs are passing regularly. If not: stop and check again. QSOs in red with ERROR? Check that your program sends the special callsign (step 3).
  • The "Send Spot" button, that you don't have in your logging program, sends a spot on the DX Cluster and can be renewed every 15 minutes just by clicking on it. It is a very useful tool: use it often.
  • The Hamaward log deletes every /QRP, /M or /7 at the end of a call (e.g. IK1HJS/7), while SP/IK1HJS, IK1HJS/SP or I7/IZ8JAI are logged normally. This is done to help the server score correctly.
Good to know
  • Send your QSOs from one program only, with one HamConnect running and one Hamaward page with Start UDP active. Otherwise your QSOs arrive twice.
  • If you can, use port 12060 in all your programs: then you never need to change it on the HamConnect page.
  • If your Internet connection drops, keep everything open: your QSOs are sent as soon as the connection is back.
  • Need help? Contact Carlo IK1HJS on WhatsApp +39 347 268 2466 or write to iw1fru@gmail.com. Tell us which program you use and, if you can, paste the text you get on the HamConnect page with Last UDP QSO raw data (button Copy).





Follow us!
©2026 All rights reserved
Powered by Ham Innovation Group
Privacy policy / Cookie policy